[Dec 04, 2021] JN0-362 Exam Dumps 100% Same Q&A In Your Real Exam
JN0-362 Test Engine Dumps Training With 67 Questions
How to Prepare for Juniper 362 Service Provider Routing and Switching Specialist (JNCIS-SP) (JN0-362)
Preparation Guide for Juniper 362 Service Provider Routing and Switching Specialist (JNCIS-SP) (JN0-362)
Introduction
Juniper 362 Service Provider Routing and Switching Specialist exam is designed for experienced networking professionals with beginner to intermediate knowledge of routing and switching implementations in Junos, this written exam verifies the candidateâÂÂs basic understanding of routing and switching technologies and related platform configuration and troubleshooting skills.
The Juniper Networks Certification Program (JNCP) Service Provider Routing and Switching track allows participants to demonstrate competence with Juniper Networks technology. Successful candidates demonstrate thorough understanding of networking technology in general and Juniper Networks service provider routing and switching platforms. This is covered in JN0-362 dumps pdf.
this written exam verifies the candidateâÂÂs basic understanding of routing and switching technologies and related platform configuration and troubleshooting skills. JNCIS-SP exam topics are based on the content of the recommended instructor led training courses, as well as the additional resources.
To earn the certification, the candidate will have to:
- Tunnels
- Layer 2 Bridging and VLANs
- IPv6
- Intermediate System to Intermediate System (IS-IS)
- High Availability
- Spanning-Tree Protocols
- Open Shortest Path First (OSPF)
- Protocol-Independent Routing
- Multiprotocol Label Switching (MPLS) and MPLS VPNs
- Border Gateway Protocol (BGP)
Exams-boost offers you the most updated JN0-362 practice exams and JN0-362 practice tests material so you can start any time. To assess your skill level and to identify gaps in your knowledge, take the practice exam and get comfortable with the material.
Who should take the JN0-362 exam
This exam is intended for learners who are pursuing routing and switching technologies and related platform configuration and troubleshooting skills.
NEW QUESTION 20
Click the Exhibit.
On an MX Series device, you must enable routing between VLANs 100,200, and the Internet ge-
5/1/0, and ge-5/1/2 are bundled into interface ae3. Ge-5/1/4, and ge-5/1/5 are bundles into interface ae2. Both AE bundles trunk VLANs 100 and 200.
In this scenario, what is the correct configuration snippet for VLAN 100?
- A. interfaces {xe-2/1/0 {unit 0{family inet {address 10.0.10.2/24;}}}ip-0/0/0 {unit 0 {family inet
{address 10.0.1.2/24;}}unit 1 {family inet {address 10.0.2.2/24;}}}}bridge-domains {vlan-
100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface xe-2/1/0.0;interface ae1.100;interface ae3.100interface ip-0/0/0.0;}} - B. interfaces {xe-2/1/0 {unit 0{family inter {address 10.0.10.2/24;}}}irb {unit 0{family inet {address
10.0.1.2/24;}}unit 1 family inet {address 10.0.2.2/24;}}}}bridge-domains {vlan- 100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface ae1.100;interface ae3.100;routing-interface irb.0;}} - C. interfaces {xe-2/1/0 {unit 0 {family inet {address 10.0.10.2/24;}}}irb {unit 0{family inet {address
10.0.1.2/24:}}unit 1 {family inet {address 10.0.2.2/24;}}}}bridge-domains {vlan- 100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface ae1.100;interface ae3.100;}} - D. interfaces {xe-2/1/0{unit 0{family inet {address 10.0.10.2/24;}}}ip-0/0/0{unit 0{family inet
{address 10.0.1.2/24;}}unit 1{family inet {address 10.0.2.2/24;}}}}bridge-domains {vlan-
100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface ae1.100;interface ae3.100;interface ip-0/0/0.0;}}
Answer: C
NEW QUESTION 21
Which two routing protocols make use of a designated router, or pseudo node, to represent a broadcast network? (Choose two.)
- A. OSPF
- B. MPLS
- C. IS-IS
- D. BGP
Answer: A,C
NEW QUESTION 22
Which three attributes are well-known mandatory BGP attributes? (Choose three.)
- A. origin
- B. AS path
- C. local preference
- D. MED
- E. next-hop
Answer: A,B,E
Explanation:
Explanation/Reference: https://www.kwtrain.com/blog/bgp-pt2
NEW QUESTION 23
Click the Exhibit button.
Referring to the exhibit, how many milliseconds must pass before the interface ge-0/0/1.0 is considered down?
- A. 900 ms
- B. 1200 ms
- C. 2400 ms
- D. 1600 ms
Answer: B
NEW QUESTION 24
Referring to the exhibit, which firewall filter action(s) will be applied to incoming frames to ge-1/0/3?
- A. Frames will be counted initially by filterA and then counted by filterB.
- B. Frames will be counted by filterB only.
- C. Frames will be counted initially by filterB and then counted by filterA.
- D. Frames will be counted by filterA only.
Answer: A
NEW QUESTION 25
Click the Exhibit button.
Referring to the exhibit what are two reasons for the configuration stanza? (Choose two.)
- A. to reduce the risk of forwarding traffic through a stateless tunnel
- B. to mark the tunnel up after the hold-time expires
- C. to mark the tunnel down after the hold-time expires
- D. to remove the tunnel interface from inet.0 after the hold-time expires
Answer: A,C
NEW QUESTION 26
Which standards-based election protocol facilities redundancy in a LAN environment by eliminating a single point failure through the use of master and backup routers?
- A. BFD
- B. ISSU
- C. VRRP
- D. graceful restart
Answer: C
NEW QUESTION 27
Click the Exhibit button.
You are asked to configure OSPF for the network? Referring to the exhibit, how should Area 1 be configured?
- A. stub area
- B. totally stubby area
- C. not-so-stubby area
- D. backbone area
Answer: A
NEW QUESTION 28
Click the Exhibit button. Which two topologies shown in the exhibit could be implemented without a spanning-tree protocol? (Choose two.)
- A. star
- B. ring
- C. mesh
- D. tree
Answer: A,D
NEW QUESTION 29
Which two statements are true about IP and GRE tunnels? (Choose two.)
- A. Tunnel endpoints need a valid route to the remote endpoint
- B. Tunnel traffic is encrypted
- C. The protocol field is changed in the inner IP packet header
- D. The TTL field is changed in the inner IP packet header
Answer: A,D
NEW QUESTION 30
Which statement is true about an OSPF broadcast link?
- A. All routers form an adjacency only with the DR
- B. All routers form an adjacency with all other routers
- C. All routers form an adjacency only with the BDR
- D. All routers form an adjacency with both the DR and BDR
Answer: D
NEW QUESTION 31
What must be configured for all IBGP speakers in an AS to have consistent routing information?
- A. Static routes to the EBGP gateways
- B. Default routes to the IBGP gateways
- C. Partial mesh of EBGP sessions between EBGP speakers
- D. Full mesh of IBGP sessions between IBGP speakers
Answer: D
NEW QUESTION 32
Click the Exhibit.
Referring to the configuration in the exhibit, which two statements are true? (Choose two.)
- A. The next-hop 172.16.1.2 must respond to ping commands for the route 192.168.5.0/24 to be active.
- B. The next-hop 172.16.1.2 must be directly connected to the router for route 192.168.5.0/24 to be active
- C. The next-hop 172.16.1.2 must be active in route table inet 3 for the route 192.168.5.0/24 to be active.
- D. The next-hop 172.16.1.2 must be part of an active route in route table inet 0 for route
192.168.5.0/24 to be active.
Answer: B,D
NEW QUESTION 33
Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of the routers.Which three configuration elements are minimally required in the baseline? (Choose three.)
- A. protocols rsvp for the appropriate interfaces
- B. protocols ldp for the appropriate interfaces
- C. family mpls on the transit interfaces
- D. protocols mpls for the appropriate interfaces
- E. family mpls on the loopback interface
Answer: A,C,D
NEW QUESTION 34
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The OSPF neighbor will be declared down if BFD hello packets are not received for 1.5 seconds
- B. The OSPF neighbor will be declared down if 500 BFD hello packets are missed
- C. The OSPF neighbor will be declared down if three BFD hello packets are missed
- D. The OSPF neighbor will be declared down if BFD hello packets are not received for 5 seconds
Answer: A,C
NEW QUESTION 35
Click the Exhibit button.
Referring to the exhibit, which statement is true?
- A. The router will attempt to signal the LSP along the IGP shortest path to 192.168.100.1
- B. The router will precalculate a valid path through the network for LSP r1-to-r3
- C. The router will prune links with insufficient bandwidth from the path before beginning the signaling process
- D. The router will analyze the traffic engineering database to determine the best path through the network
Answer: A
NEW QUESTION 36
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. Interface ge-1/0/0.0 can only form a single adjacency
- B. Interface xe-0/0/0.0 can only form a single adjacency
- C. Interface xe-0/0/0.0 has a default metric of 10
- D. Interface ge-3/0/0.0 has a default metric of 10
Answer: A
NEW QUESTION 37
Click the Exhibit button.
You must create a static route on Router-A to the 10.10.5.0/24 network using 10.10.3.2 as the next hop.
Referring to the exhibit, which configuration accomplishes this task?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 38
Your customer would like to forward traffic using DLCI 600 and maintain Layer 2 information across a VPN.Which solution will meet these requirements?
- A. a Layer 2 VPN
- B. Virtual Private LAN Service (VPLS)
- C. an IPsec VPN
- D. a Layer 3 VPN
Answer: A
NEW QUESTION 39
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. R1 is a backbone router
- B. R2 is an ABR
- C. R1 is an ABR
- D. R2 is an ASBR
Answer: B
NEW QUESTION 40
You are adding nonforwarding route reflectors to your network. Which three actions ensure that VPN routes are advertised properly? (Choose three.)
- A. Add the route reflectors to the same IGP domain as their clients.
- B. Use rib-groups to add IGP routes to inet.3 and/or inet6.3 on the route reflectors.
- C. Use rib-groups to add VPN routes to inet.0 and/or inet6.0 on the route reflectors.
- D. Add MPLS LSPs between the route reflectors and their client routers.
- E. Add a static default route to inet.3 and/or inet6.3 on the route reflectors.
Answer: B,D,E
NEW QUESTION 41
Click the Exhibit button.
Referring to the exhibit what are two reasons for the configuration stanza? (Choose two.)
- A. to reduce the risk of forwarding traffic through a stateless tunnel
- B. to mark the tunnel up after the hold-time expires
- C. to mark the tunnel down after the hold-time expires
- D. to remove the tunnel interface from inet.0 after the hold-time expires
Answer: A,C
NEW QUESTION 42
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. Interface ge-1/0/0.0 can only form a single adjacency
- B. Interface xe-0/0/0.0 can only form a single adjacency
- C. Interface xe-0/0/0.0 has a default metric of 10
- D. Interface ge-3/0/0.0 has a default metric of 10
Answer: A
NEW QUESTION 43
Click the Exhibit button.
Referring to the exhibit, which statement is true?
- A. The router will prune links with insufficient bandwidth from the path before beginning the signaling process
- B. The router will precalculate a valid path through the network for LSP r1-to-r3
- C. The router will analyze the traffic engineering database to determine the best path through the network
- D. The router will attempt to signal the LSP along the IGP shortest path to 192.168.100.1
Answer: A
NEW QUESTION 44
......
Juniper JN0-362 Exam Topics:
| Section | Objectives |
|---|---|
| Intermediate System to Intermediate System (IS-IS) | Identify the concepts, operation, or functionality of IS-IS
Demonstrate knowledge of how to configure, monitor, or troubleshoot IS-IS
|
| Open Shortest Path First (OSPF) | Identify the concepts, operation, or functionality of OSPF
Demonstrate knowledge of how to configure, monitor, or troubleshoot OSPF
|
| High Availability | Identify the concepts, benefits, applications, or requirements of high availability
Demonstrate knowledge of how to configure, monitor, or troubleshoot high availability components
|
| Multiprotocol Label Switching (MPLS) | Identify the concepts, operation, or functionality of MPLS
Demonstrate knowledge of how to configure, monitor, or troubleshoot MPLS
|
| Border Gateway Protocol (BGP) | Identify the concepts, operation, or functionality of BGP
Demonstrate knowledge of how to configure, monitor, or troubleshoot BGP
|
| Protocol-Independent Routing | Identify the concepts, operation, or functionality of various protocol-independent routing components
Demonstrate knowledge of how to configure, monitor, or troubleshoot various protocol-independent routing components
|
| Spanning-Tree Protocols | Identify the concepts, benefits, operation, or functionality of Spanning Tree Protocol and its variants
Demonstrate knowledge of how to configure, monitor, or troubleshoot STP and its variants
|
| Layer 2 Bridging or VLANs | Identify the concepts, operation, or functionality of Layer 2 bridging for the Junos OS
Identify the concepts, benefits, or functionality of VLANs
Demonstrate knowledge of how to configure, monitor, or troubleshoot Layer 2 bridging or VLANs
|
| IPv6 | Identify the concepts, operation, or functionality of IPv6
Demonstrate knowledge of how to configure, monitor, or troubleshooting IPv6
|
| Tunnels | Identify the concepts, requirements, or functionality of IP tunneling
Demonstrate knowledge of how to configure, monitor, or troubleshoot IP tunnels
|
JN0-362 Practice Test Pdf Exam Material: https://www.exams-boost.com/JN0-362-valid-materials.html