[Oct 20, 2021] Exams-boost 300-610 dumps & CCNP Data Center sure practice dumps
Cisco 300-610 Actual Questions and Braindumps
3. Storage Network Design
- Weightage allotted – 20%
The principal focus of this part of the exam content is on skills related to iSCSI deployment in a given data center ecosystem and QoS requirements, including the use of Fibre Channel, FCoE, FCIP, and iSCSI. Then, the applicants should have a solid understanding of the key ways to determine FCoE along with Fibre Channel interface. This involves the concepts of oversubscription, the type of ports, shared and dedicated modes, and ISL. SAN topology options are also included in this section.
Exam Overview
Before going for the Cisco 300-610 test, you need to know the details of its structure and syllabus to be ready for the application. Thus, it is important to know that you will be given 90 minutes to clear 60 multiple-choice questions. To pass the exam, you should gain at least 825 points. Also, please note that the test is available in the English language and the voucher will cost you $300.
NEW QUESTION 31
Refer to the exhibit.
What must be the default gateway of the servers in EPG Web?
- A. NAT appliance
- B. subnet address of BD2
- C. subnet address of BD1
- D. subnet address of L3Out
Answer: A
Explanation:
Section: Network Design
Explanation/Reference:
NEW QUESTION 32
An engineer needs an orchestration and monitoring tool that should be used for managing the storage networks and VXLAN fabrics. The tool should also allow support built-in dashboard and real-time health summary for managed devices. Which tool meets these requirements?
- A. Cisco Intersight
- B. Puppet
- C. Ansible
- D. Cisco DCNM
Answer: D
NEW QUESTION 33
An engineer must design a VXLAN EVPN network. The solution should optimize broadcast, unknown unicast, and multicast (BUM) and short BUM replication, and use PIM anycast RP. Which solution should be included in the design?
- A. PIM sparse mode
- B. ingress replication
- C. PIM dense mode
- D. head-end replication
Answer: A
NEW QUESTION 34
Which two configurations are available by using a service profile template in Cisco UCS Manager? (Choose two.)
- A. VXLAN membership
- B. ARP entries
- C. target server
- D. number of vHBAs
- E. UUID assignment
Answer: D,E
Explanation:
Section: Automation Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/cli/config/guide/2-2/ b_UCSM_CLI_Configuration_Guide_2_2/b_UCSM_CLI_Configuration_Guide_2_2_chapter_0100000.html
NEW QUESTION 35
Which Ethernet to Cisco Fabric Interconnect connectivity configuration is supported when FCoE is implemented?
- A. Ethernet and unified ports on the same port channel
- B. VSS that has unified uplinks
- C. vPC that has unified uplinks
- D. cross-connections with pinning
Answer: C
Explanation:
Section: Storage Network Design
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/servers-unified-computing/ucs-manager/116188- configure-fcoe-00.html#anc11
NEW QUESTION 36
Which type fields can an engineer use to identify an iSCSI participant? (Choose two.)
- A. port number
- B. preshared key
- C. hostname
- D. type
- E. identifying tag
Answer: A,C
Explanation:
Section: Storage Network Design
Explanation/Reference: https://en.wikipedia.org/wiki/ISCSI
NEW QUESTION 37
Refer to the exhibit.
A high-availability setup for iSCSI is designed with the host running ISCSI software. Each storage port on the MDS exports the same two Fibre Channel target ports with different ISCSI target names. In this design, how many ISCSI session are created from the host so that recovery occurs if any component fails?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
https://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_3_x/configuration/guides/fm_3_2/ciscsi.html
NEW QUESTION 38
Which factor determines the choice of platform designing a Cisco HyperFlex infrastructure to support computer-aided design applications?
- A. GPU support
- B. processor count
- C. storage capacity
- D. network speed
Answer: C
NEW QUESTION 39
Drag the appropriate from the left onto the current UDLD modes of operation on the right.
Answer:
Explanation:
NEW QUESTION 40
An engineer is designing a Multichassis EtherChannel topology in which two switches must appear as a single device to a third downstream switch? Which two technologies meet this requirement? (Choose two.)
- A. vPC
- B. 802.1q
- C. VSS
- D. HSRP
- E. FEX
Answer: A,C
Explanation:
Section: Compute Design
Explanation/Reference: https://www.cisco.com/c/dam/en/us/products/collateral/switches/nexus-7000-series-switches/C07-
572835-00_NX-OS_vPC_DG.pdf
NEW QUESTION 41
Which type of encoding is used on 8-Gbps links as compared to 10-Gbps links?
- A. 8-Gbps links and 10-Gbps links use 64B/66B encoding.
- B. 8-Gbps links use 64B/66B encoding, and 10-Gbps links use 8B/10B encoding.
- C. 8-Gbps links and 10-Gbps links use 8B/10B encoding.
- D. 8-Gbps links use 8B/10B encoding, and 10-Gbps links use 64B/66B encoding.
Answer: D
NEW QUESTION 42
An engineer is implementing a storage area network where an NPV is used. The engineer notices that the servers in a storage farm are experiencing heavy traffic contention. The engineer needs to migrate traffic from heavily loaded server interfaces to interfaces with less load. When the new links are deployed, the existing traffic is not rebalanced as expected. Which feature must be used to meet these requirements?
- A. disruptive load balancing
- B. DVM
- C. multiple VSAN support
- D. NPIV
Answer: D
NEW QUESTION 43
An engineer configured the OSPF protocol in the vPC topology. During the catastrophic failure of one of the vPC the member switches, the traffic was routed to a black hole. This route was caused by the long convergence time caused by the delay of the of the vPC member switch reboot. After the failure, the engineer rebooted both switches, but the secondary switch powered on before the primary one. It caused all the vPCs to be shut down due to consistency-check violations. Which two features must be used to prevent these situations from happening in the future? (Choose two.)
- A. system priority
- B. peer-gateway
- C. delay restore
- D. ip arp synchronize
- E. auto-recovery
Answer: C,E
Explanation:
System priority is related to LACP, not vPC, so it is out. ARP s
Reference:
https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/nx-os-software/212589-understanding-vpc-election-process.html
NEW QUESTION 44
Refer to the exhibit.
An engineer must assign multiple Fibre Channel IDs to a single port channel. Which two features must be enabled this goal? (Choose two.)
- A. NPV feature on the Cisco MDS Series.
- B. Smart Zoning feature on the Cisco UCS Fabric Interconnects
- C. end-host mode feature on the Cisco UCS Fabric Interconnects
- D. SAN Pin Groups on the Cisco UCS Fabric Interconnects.
- E. NPIV feature on the Cisco MDS Series
Answer: A,E
NEW QUESTION 45
Which approach splits a pair of clustered fabric interconnects into two standalone devices?
- A. Erase the configuration of both fabric interconnects.
- B. Run the connect local-management command on each fabric interconnect.
- C. Run the disable fips-mode command on each fabric interconnect.
- D. Unplug the Layer 1 and Layer 2 interfaces between the devices.
Answer: D
Explanation:
Section: Compute Design
NEW QUESTION 46
Which multicast rendezvous point redundancy mode is valid for Bidirectional PIM?
- A. Embedded RP
- B. PIM anycast RP
- C. Phantom RP
- D. MSDP
Answer: B
Explanation:
Section: Network Design
Explanation/Reference: https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ip-multicast/whitepaper_c11-
508498.html
NEW QUESTION 47
Refer to the exhibit.
An engineer must assign multiple Fibre Channel IDs to a single port channel. Which two features must be enabled this goal? (Choose two.)
- A. NPV feature on the Cisco MDS Series.
- B. Smart Zoning feature on the Cisco UCS Fabric Interconnects
- C. end-host mode feature on the Cisco UCS Fabric Interconnects
- D. SAN Pin Groups on the Cisco UCS Fabric Interconnects.
- E. NPIV feature on the Cisco MDS Series
Answer: A,E
NEW QUESTION 48
What are two functions of a Network Services Orchestrator in an NFV environment? (Choose two.)
- A. It operates at the customer-facing services layer and provides the management interface for the virtual network devices.
- B. It provides a standards-based northbound interface for transparent integration with systems that operate at the customer-facing services layer.
- C. It provides an API-based northbound interface for transparent integration with systems that operate at the resource-facing services layer.
- D. It operates at the resource-facing services layer and provides overall lifecycle management at the network service level.
- E. It provides a standards-based southbound interface for transparent integration with systems that operate at the customer-facing services layer.
Answer: C,D
Explanation:
Section: Automation Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/net_mgmt/msx/3_4/solution_overview/ Cisco_VMS_Sol_Overview.pdf
NEW QUESTION 49
A client in a commercial building Installs a Cisco blade server in the multitenant Cisco UCS blade Infrastructure. To cut operating costs me client's data center is shared with other organizations. The client asks an engineer prevent third parties from accessing their equipment and from accessing BlOS-related information when booting a server. Which Two policies must be used to meet these requirements? (Choose two.)
- A. CDN control
- B. ASPM support
- C. post error pause
- D. front panel lockout
- E. quiet boot
Answer: A,E
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Server-Mgmt/3-2/b_Cisco_UCS_Manager_Server_Mgmt_Guide_3_2/b_Cisco_UCS_Manager_Server_Mgmt_Guide_3_2_chapter_01110.html Quiet boot is what the BIOS displays during booting the server. If enabled, the BIOS displays the logo screen.
I believe that quiet boot and CDN control may have the customer name.
NEW QUESTION 50
DRAG DROP
A failure occurs on the network between two BFD and OSPF neighbors. Drag and drop the protocol actions from the left into the correct order on the right.
Select and Place:
Answer:
Explanation:
Section: Network Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/fs_bfd.html#wp1238898
NEW QUESTION 51
......
2. Compute Design
- Weightage allotted – 25%
This is the second most considered area one has to master. The candidates will have a fair chance to learn about available options for Ethernet connectivity, storage connectivity, and network device virtualization in a data center. Common types of interfaces, vCon placement policies, Ethernet adaptor policies, and Fibre Channel adapter policies are also covered diligently in this domain. Before it ends, never forget to give a quick overview of key evaluation options required for hyper-converged infrastructure. Finally, the topics like a cluster mode, desktop virtualization, and HX use for the virtual server are discussed.
Latest 300-610 Pass Guaranteed Exam Dumps with Accurate & Updated Questions: https://www.exams-boost.com/300-610-valid-materials.html
Pass 300-610 Exam with Updated 300-610 Exam Dumps PDF 2021: https://drive.google.com/open?id=18HIe75D-uA-YrWX8eiSYH7VI-u_684js